1/76th Panzerkampfwagen IV - The Sequel

If you had more endurance than sense or were seeking a cure for insomnia and have stuck with this so far you may have wondered what happened to the Cromwell Models Pz IVH turret? 

I have an ongoing project to build some Berlin '45 terrain and on looking at the Battlefront Flames of War website I noticed that they produced a Pz IV turret bunker. That solved that , I hated the thought of that nice looking turret being consigned to the spares box for eternity.

I pulled the page up on the BF site on my iPad as inspiration and then measured and cut the pieces.  The top part was plastic card and the bottom part was cut from the the back of an old picture frame. I cut the bottom off the Pz IV turret to make it flush and then drilled a central hole with the pin vice. I was a little overzealous here and ended up drilling all the way through. This actually turned out to be helpful though as I placed this in the correct place on the bases and just drillled through the lot with the old pin vice. 

To add some texture I glued some wet and dry paper to each rectangle and then stuck them together with PVA.  When it was dry  I painted with various shades of grey. I think I used Privateer Press Bane Base and then Coat D'armes dark grey. I then drydrushed lighter shades of grey. The turret was attached with a piece of brass rod. I carefully filled the drill hole with green stuff and built up the missing piece of rim with green stuff.

The turret was basecoated with a mix of VMC Middlestone and VMC White and then washed with VMC Umber Wash. I used Citadel Devlan Mud to add further depth where required. I then added highlights with Middlestone mixed with more white. 

 

1/76th Panzerkampfwagen IV - Pt 4 (of 4) The End or is it?

So after painting both models I though it'd be a simple thing to add the schurtzen. Think again. When I lined them up I realised that one side fitted snugly and the other didn't. So I ended up hacking off all the inner supports and in the process cutting off one of the support rails. AARRRGGGGH. Luckily I'd had the sense to give the models a good couple of coats of varnish so I didn't do too much damage to the camo finish. They fitted quite nicely after that with liberal use of Super Glue.

You'd have thought that by now I'd call it a day. No I wanted more pain so I cut some 1mm wide plastic card strips to make the schurtzen rail supports.I slightly shaped each end and fitted with not so liberal use of Super Glue.

With plastic card side supports added

And that my friends was that, apart from when I was showing boring my wife with what I'd done I saw that the turret was missing a schurtzen support. So I had to make a plastic card one. And paint it. And while I had the paint out I added a number of highlights to all the edges. And that really is that.

Cromwell hull, Fujimi turret

Cromwell hull, Fujimi turret

Cromwell hull, Fujimi turret top view

Turret and both hulls

Fujimi hull and turret

Fujimi hull and turret

1/76th Panzerkampfwagen IV - Pt 3 (of 4) - it's a saga now

Right with all the fiddly, fussy, fixing done (or so I thought) I could get down to painting. 

First off I painted the tyres and rollers. These got the usual coat of Vallejo Model Colour German Grey (VMC 995). By using a brush with a decent point and keeping a small moistened brush to hand I managed to do these without getting paint all over the inner parts of the wheels.

For the main assemblies both of them had originally been painted in my usual Dunkelgelb finish which was Humbrol 83 Matt Ochre and Humbrol 34 Matt White mixed to about 65/35 ratio. On digging through my box of enamels I found that both tins of the fore mentioned colours had dried out! So I reached for the Vallejo and mixed VMC Middlestone  (VMC 882) with VGC White to get an ok if quite light base colour.

Base coated and looking very light

Using the Osprey Modelling the Late Panzerkampfwagen IV I chose the model that had the most complete set of photos showing the camo pattern from the most angles. This was a PZIV H from 5th Panzer in 1944 which fitted my gaming period. 

I started with the Cromwell kit and drew the pattern on in pencil then painted the colours in. I used Citadel Calthan Brown and Knarloc Green paints that I got cheap years ago when the last local toy shop closed down and they looked ok. I wasn't really too bothered about the correct RAL numbers as I was going to do a lot of weathering. Once I'd got the camo on I then applied a watery wash of the base Dunkelgelb to tone it all down. This worked better than I thought. The final stages were to apply various washes of VMC Umber Wash and then Citadel Devlan Mud to the areas I wanted to add more depth to. 

Fujimi (L) base coat, Cromwell painted

Fujimi with basic camouflage

Fujimi with Dunkelgelb wash

Using the Cromwell kit as the master I then repeated the process for the Fujimi body. 

I then painted all the tools, exhausts etc. Here's how the Cromwell kit was looking prior to adding the schurtzen where you can see the tools more clearly.

1/76th Panzerkampfwagen IV - Pt 2 (of 4) - fixing

Part 1. The Fujimi turret. Looking at the invaluable Osprey Modelling Guide no 38, Modelling the Late Panzerkampfwagen IV there wasn't too much difference between a H and a J turret. I simply removed the machine gun from the Fujimi model as both the H and J models detailed in the book didn't have one The H model should have zimmerit on the turret schurtzen but I can live without this, especially when you see how many wargamers have used non-zimmerit models for years.

Part 2. The Cromwell Pz IVH hull. This was a lovely detailed piece, with nice zimmerit and stowage moulded on. The only problem was the lack of side schurtzen. My initial thought was to use the ones off the Fujimi kit. However. these were supposed to represent the wire mesh ones that Pz IVJs had and were wrong for an H. Going through the spares box I found a set of metal schurtzen that came from an SHQ Sturmpanzer IV. Although slightly too small they had the correct number of plates (5) and would do the job. I bent some florist wire round the top of each schurtzen to shape it and then stuck it on the inside to represent the fixing rail. Fixing them was another matter but this would wait until the finishing stage.

Schurtzen  - before

Schurtzen - with rails added

The only other work needed on the Cromwell body was to drill a small hole and add an MG34 barrel from the spares box.

While I was doing all this I started to think about what I could do with the Cromwell turret and Fujimi body. I then decided that I'd repair the Fujimi body and paint it in the same scheme as the Cromwell body/Fujimi turret hybrid. That way I'd have a PZ IVJ to use if I ever wanted to. So I now increased my work load.

Part 3. The Fujimi Pz IVJ hull. When I removed the schurtzen I  pulled a couple of the track return rollers off one side and they pinged across the room never to be seen again. As I was going to model this without the side-skirts I needed to do some repair work. The surviving rollers were each made of two identical pieces glued back to back. By separating these it gave me the correct number of parts for a bodge/repair. For three of the rollers I removed the roller sections completely. I then attached a suitable size metal pin. Over this I slipped a small piece of plastic rod. Finally I added the correct roller. If you look closely and at a particular angle you'll see the rear roller is a little small but in normal use you'd never see it. I then straightened out and re-glued the tracks. 

Fujimi body with track rollers removed

Fujimi body with new rollers added

To finish the body I removed the flimsy exhausts, drilled holes and then slightly countersunk them to make them sturdier. Finally I added a new hull machine gun as above.

1/76th Panzerkampfwagen IV - Pt 1 (of 4)

Anyone that has read my start and end of month progress posts may have noticed the ever present Cromwell Models Pz IVH. I bought this back in 2014 and it's been sitting either on my table or at difficult times banished to a drawer ever since. I even referred to it as my bête noire at one stage.

Like all Cromwell Models offerings it's a lovely kit, so what was the problem with it? The problem was it needed a lot of work. As I wrote in September "It's a resin kit with incredibly fragile turret schurtzen. All of the supports were either broken when I got it or have broken just by looking at them. Additionally the model didn't come with the side schurtzen or with the supports on the model which is pretty poor as all Pz IVHs had them."

When I got my WW2 mojo back on in October/November time I had a burst of inspiration. I have a poor old Fujimi Pz-IVJ that has seen better days built many years ago. Why not use the best of each kit to make a half decent model? 

The kits as they have appeared since 2014 - Fujimi PZIVJ on the left, Cromwell PZIVH on the right.

So that's what happened and if you want to read on you can see what I did in excruciating detail - I want you to share my pain.